Older releases.

← Newer releases

2.26.0

2026-10-21 · build 2522

Added

  • Master, every bus and Solo / Monitor can each play on a device of their own. In Audio Device Setup, each has its device and its channels side by side on its row, so Master can go to an interface, an interpreter's bus to another and the headphones to the Mac's own output. A bus is named on its own row, and its colour is the dot before the name. Every device is kept in time with the Mac, so sound never skips or falls silent however long the show runs, and mixes on different devices leave the Mac together. The engine section shows each device's drift and wait, and the journal says when a device skipped sound or ran dry, which should now be never.

  • Framing presets: keep a source's or a Composite layer's whole framing — position, size, crop, rotation, corners and border — with Save as Preset… in its framing editor, and recall it onto any source or layer from a hotkey, a rule, the Stream Deck's new Framing Preset action, Bitfocus Companion (module 0.1.22) or the control API. The picture glides there over the time you set, or jumps at 0, and a key is lit while the framing matches. Presets are numbered and named, and renamed, put in order, updated and deleted in Show Settings › Framing Presets, and Apply Preset puts one on the picture you are framing. A Show saved with this version opens only in this version or later.

  • InterDirector Cam lowers its bitrate when its picture falls short on the way to InterDirector, not only when its own upload does: InterDirector, and the relay when it comes over the internet, tell the phone, which climbs back once things hold. Adaptive bitrate must be on in the app. The Show's journal says when a phone was asked to lower its bitrate, and when it is back.

  • Stop All Relays and Free the Server, in a network input's Over the internet settings, stops every stream your licence receives over the internet and shuts its relay server down at once, instead of 15 minutes after the last stream stops. Addresses are kept. Release Addresses No Open Show Uses is now offered at any time, not only once all six addresses are taken.

Changed

  • Applying a change in Audio Device Setup no longer restarts audio: the stream, the recording and NDI carry on while the outputs move, and only the device whose mixes changed is reopened. Solo / Monitor on a device of its own no longer glitches now and then.

  • The framing editor's settings open and close by section, and it remembers which you keep closed; a closed one says what it is set to. Corner rounding and the loop start closed.

  • On a new Mac, you hear Master through Solo on the Mac's own speakers or headphones, with nothing to set up. Master no longer needs an output of its own: choose Enabled for it in Audio Device Setup, as for a bus. Macs already set up keep their setup. Solo is now called Solo / Monitor in the mixer and in Audio Device Setup.

  • The top bar says "Check audio setup" only when nothing plays on this Mac, neither Master nor Solo, and clicking it opens Audio Device Setup. Audio Device Setup warns when nothing would play here.

  • A source card shows a speaker in place of the word "muted": crossed out while the source is muted, and a speaker for a source with sound of its own, which turns bright green while its sound is on air. A source that follows Program goes green as it goes to Program, a microphone with the camera it is paired to; one that does not is green whenever it reaches Master. Cards with no sound of their own show none, so you can tell at a glance which carry sound.

  • The Show's journal says where each recording goes: the folder in full, so you can tell which disk, and how much room that disk had as it started. For the Program recording, each input's own recording, replay clips and pieces exported at cut marks; and a recording folder you have chosen is written as the Show opens and whenever you change it.

Fixed

  • An external display keeps what it shows when it is plugged in later. macOS can give a display a new number when it comes back, such as a monitor plugged in after InterDirector started, and External Output then listed it twice: Off as connected, and its old choice as not connected. A display is now known by its own identity, so it keeps its choice, and the extra entry goes the next time External Output is opened or the output starts. A display that is not connected has a button to forget it, so displays from past venues do not pile up.

  • The framing editor keeps a picture's frame and handles in view when it reaches past the canvas, such as a large picture moved down; they were cut off at the edge of the preview.

  • A phone's Camera window shows its controls at once, however long after the phone connected you open it. It waited for the phone's camera to change first, such as a touch of zoom.

2.25.0

2026-10-19 · build 2476

Changed

  • A new SRT input has a stream ID of its own, as an RTMP input has its key: only a sender presenting it is taken, so a stray sender cannot put a picture on your card. Press New ID for another, or clear it to take any sender. An SRT input you already have with no stream ID keeps taking any sender; one where you typed a stream ID now takes only a sender presenting it, as its settings always said.

2.24.0

2026-10-19 · build 2472

Changed

  • A split source's two strips stand apart in the audio mixer, with extra space before and after the pair, so you can tell them from two sources side by side.

2.23.1

2026-10-19 · build 2470

Fixed

  • Opening a Show while your audio interface is unplugged no longer leaves it without sound. The mix runs, the meters move, and the stream, the recording and NDI have their sound; the top bar says which device it is waiting for, and the sound comes out of it as soon as you plug it in, with no Retry.

2.23.0

2026-10-19 · build 2468

Changed

  • ReCast's page shows Program alone, no longer the incoming stream beside it, and its Instagram and TikTok picture is sent at 30 frames a second when the Show runs faster, so its server has more to spare.

Fixed

  • A Web source can take a microphone's sound, as a camera or an image can: tick it in the Web source's Audio settings, and it goes to Program with the page.

2.22.1

2026-10-18 · build 2460

Fixed

  • ReCast's Copy Login also copies the page's address, so a colleague has where to sign in as well as the login.

2.22.0

2026-10-18 · build 2458

Added

  • The mouse pointer shows on a multiview display, and hides itself when still.

  • Clicking a source on the multiview display can put it in Preview, or cut, fade or dip it to Program: choose Clicking a source in the multiview layout window. A new Show starts at Do nothing.

Fixed

  • Tabs that do not fit can be reached with a mouse: in the Replay, Media and Data panels and the source colour tabs, drag the row of tabs sideways, or turn the mouse wheel over it. Before, only a trackpad could scroll them.

2.21.0

2026-10-17 · build 2453

Fixed

  • Pictures now stay in step with the sound when audio effects delay it. Effects that look ahead, such as limiters and noise reduction, delay the sound a little; every picture now waits for them too, on Program, every output and the monitors, so lip sync holds without measuring again after adding or removing an effect. Settings ▸ Audio says how much they add.

  • A switched-off audio effect no longer delays anything. Its delay was still counted, so a source with one switched off played ahead of the others.

  • Quitting no longer crashes with some audio effects loaded, such as Waves effects: InterDirector now stops its audio before it quits.

Changed

  • Sync Cameras and Audio's Global extra delay is now the Reference audio delay, with a lock. Set the delay the reference sound needs in your venue and lock it: measuring then fits every camera and sound around it and never changes it, and says how much it must be raised when a camera is too far behind to catch up. Changing it moves every ticked camera and sound with it. A Show that used the global extra delay opens with it added to each source's own delay, so nothing moves. Reset and Clear Delays now keeps the reference delay.

2.20.1

2026-10-17 · build 2436

Fixed

  • InterDirector no longer freezes at launch when it finds an update. In 2.20.0, an update found while the startup window was open put up a window that could not be clicked, and InterDirector could not be quit. If that happens to you, force quit InterDirector (Option-Command-Esc) and install this version from interdirector.com/download.

2.20.0

2026-10-17 · build 2434

Added

  • Sync Cameras and Audio shows what is ready before you measure. The sound row says whether it hears the phone's beep, with a meter of how loud it is; each camera has a small live picture with a box where it sees the phone, and says whether it sees it or what to try.

  • Global extra delay in Sync Cameras and Audio moves the sound and every synced camera and sound together, on top of each one's own delay, even during a show. Setting it back to 0 returns them exactly to where syncing left them. Input Settings shows it beside a source's own delay.

  • Other sounds can be lined up in Sync Cameras and Audio too: tick them, and each is measured against the chosen sound by the same beep.

  • The sync page on the phone has a short checklist, a Test beep that plays the beeps once without flashing, how long it has been running, and a Double-tap to stop reminder at the bottom while it flashes.

Changed

  • Measuring cameras in turns no longer needs unticking: a camera keeps its last reading in which it saw the phone, so keep them all ticked and turn the phone to each in turn.

  • After Apply, Sync Cameras and Audio measures again by itself, so each source says whether it is now in step.

  • The sound and the sources ticked in Sync Cameras and Audio are saved with the Show.

  • Sync Cameras and Audio opens filling the screen, in two columns: the sources to measure on the left, the results on the right, with Measure and Global extra delay always in view however many sources there are.

  • Updates are looked for the moment InterDirector starts, not once a Show has opened, and every hour while it stays open. One found while the startup window is open is shown in front of it, ready to click; choose Later and the startup window comes back.

2.19.0

2026-10-17 · build 2417

Added

  • New and updated VST3 effects are found by themselves when InterDirector starts: only what changed is read, in the background, and a notice names it. No more Rescan after installing an effect.

  • An effect that crashes or hangs while being read no longer takes InterDirector with it. Effects are read in a process of their own; a bad one is left out, named in a notice, and listed in Settings ▸ Effects with Try Again. It is read again by itself once it is updated.

2.18.0

2026-10-17 · build 2412

Added

  • Sync cameras and audio: line up every camera's picture with the sound. Choose Tools ▸ Sync Cameras and Audio…, have someone on stage open the page its QR code points to on a phone, and press Measure: InterDirector says how far each camera's picture is from the stage microphone's sound, and the delays that line them all up. Apply them one at a time or all at once. Tick the cameras to measure; ones that cannot all see the phone can be measured in turns.

  • Change a source's type, keeping everything else. Right-click a card and choose Change Source Type…, or press Change… beside Type in its settings, to make a camera into an NDI or Blackmagic source, or a microphone into a camera, and so on. It keeps its name, sound, rules, and every hotkey and button that names it. If the new type cannot keep something, such as colour correction on a source that becomes sound alone, you are told what goes first. A rule or hotkey that no longer fits is kept and marked, so changing the type back makes it work again.

  • Several sounds can follow one camera. In a source's Audio tab, Audio Source is now a list of tick boxes: tick every microphone that should come up with it on Program, and its own sound too if it has any. Each keeps its own mixer strip.

Changed

  • Shows saved by this version cannot be opened by an earlier one.

Fixed

  • InterDirector Camera and InterDirector Audio are no longer offered as sources. They carry your Show out to meeting apps, so taking them back in only fed Program into itself.

  • A network or window input with a sync delay played no sound. Its sound now waits with its picture, as every other input's does. Its own recording is timed after the delay too.

Older releases

Contact support

Or write to support@interdirector.com. From InterDirector itself, Help → Report an Issue… sends the logs with your message. See the privacy notice for what the chat keeps.